Asus password- Forgot your password?
If your ISP provided you with your router, you can try calling them and see if they know your router's username and password, or maybe they can reset it for you.
If you still can't log in, you may have to reset your router to default settings.
It's possible that your router's default password is different from what we've listed here.
Some ISPs prefer to abuse DNS system and match unknown names to the servers they manage. This can be done without you knowing what's going on as your router gets its DNS settings from your internet service provider. For example, if you have one of these ISPs that are hijacking your DNS, and you try to surf the Internet to "some-random-site.com" and "some-random-site.com" doesn't exist, you might get a page back from your ISP with local advertising on it.
By changing the DNS setting on your router, you are effectively changing the DNS setting for every computer on your network. This is because when a device is connected to your network, your router automatically transmits its own settings DNS for this device. So you can protect your entire network from ISP hijacking with one parameter.
If you followed our registration guide above, you should see this screen.
To change settings domain name systems, click on the selection on the left side of the page labeled " LAN", located under additional settings.
On this new page, click the tab at the top of the page that says DHCP Server.
You are now on a page similar to the one you see above. Scroll down the page until you reach the section with DNS and WINS Server settings .
In the specified field DNS server Enter the primary IP address of the DNS server you selected.
Most routers have at least two spaces for the primary and secondary addresses. ASUS RT-N66U only has space for the main address. Since you rarely need a secondary address, this shouldn't be a problem, but if you find one, you may need a different router.
For children: best apps for children on iOS or Android.
When you're done with the changes you want to make, click the " Apply" at the bottom of the page.
Most devices on your network will not start using the new DNS settings until they are rebooted. After your device restarts, you can go to its network settings and make sure it uses the DNS servers you specified.
After you have completed logging in Asus RT-N66U, you got to network map router. Find the link on the left side of the page that says WAN, it is under the heading “ Additional settings» . This will open new page up, select the tab at the top labeled Virtual Server / Port Forwarding .
Set up the Port Forwarding section of your Asus
Now to forward the port, make the following changes:
Now you are on correct page. Scroll down until you see port forwarding list. Underneath this service name enter something that reminds you of why you are forwarding these ports, such as the name of the program.
Next to this range ports enters the port number in this field if you are forwarding multiple ports then enter them as a list like 22,23,24, a range like 22-25 or a combination like 22, 23, 25-27.
To the right of this is local IP-the IP address you forward to these ports into this field. If you are forwarding a port to run a program on your computer, you should use that computer's IP address here.
After this there is local port. Enter the same numbers you entered in port range, you can enter ports as a list, a range, or a combination of both.
When you finish all this, click the button Add" right and then " Apply" below. That's all!
If your router is not working, buy a new one.
Before you start setting up the router, you will need to prepare your computer for further customization, as well as clarify some of the connection parameters. How to do this is described in detail in our instructions: ! When the computer is ready, we proceed directly to setting up the router.
Connecting the router:
Wait until the lights on the router light up power diodes (PWR), active first port (LAN1) And WLAN (AIR), although it happens that the latter is disabled in the router settings.
Setting up the ASUS RT-N10 router
2.
IN address bar indicate the IP address of the router: http://192.168.1.1
After entering the address, an authorization window will appear on the screen to access the router settings ( Rice. 5). To enter the configurator, enter:
3. Not experienced users the system will offer an attempt to set up an automatic connection through the configurator, for which just click “ Further": Rice. 6
4. If your provider provides the Protocol - Static IP address and exactly 192.168.1.1 (how to find out what protocol you have is described in detail in our instructions: Preparing the PC before setting up a Wi-Fi router), which coincides with the router’s IP address, in the “ LAN", in the tab LAN IP address, you should change the router's IP address to 192.168.100.1 , then press “ Apply"and reboot the router. We also reboot the computer and re-enter the router through the browser, but through a new IP address ( Rice. 7):
5. If the protocol is different from the above or your operator has a different IP address, skip Point 4.:
6. If auto-tuning does not complete successfully, go to the “ WAN", where from the list we select the Protocol of your operator ( PPPoE, PPTP or L2TP):
7. Depending on the provider, IP addresses and DNS are provided automatically or must be entered manually. We will also learn these parameters from the instructions: Preparing the PC before setting up a Wi-Fi router. We indicate in the window Username And password, according to the requirements of the operator, and binding, if necessary, to the physical address:
8. After applying and rebooting the router, enter the settings section Wireless network.
According to the above picture, you should specify the parameters future network WiFi:
In order to configure an ASUS router there are two ways. The first is to take advantage special master quick setup devices. It is specially integrated into the web configurator so that an unprepared novice user can easily connect the router to the provider’s network and raise wireless network Wi-Fi. Of course, its capabilities are very limited, but it allows you to configure the most basic functions of the router without any problems.
The second way is to work with a full-fledged web interface, which allows you to fully reveal the full potential of the device, if necessary, squeezing out of it everything that it is capable of. Let's consider each of the options separately.
In both cases, in order to enter the configuration interface of the Asus router, you need to enter the device’s IP address in the address bar of your web browser - 192.168.1.1 . When prompted for authorization, enter the login "admin" and password "admin".
When you first access the web configurator, you will see a wizard prompt to quickly configure the device. We agree. The first step is to change the default access password:
Instead of the default "admin" use any other one. It is desirable that it be more or less complex: consist of 7-8 characters, contain letters of the Latin alphabet, numbers and Special symbols @#$%&.
The next step is to select your Internet connection type:
Asus routers can work on almost any network Russian Internet provider - Rostelecom, Dom.ru, TTK, etc. The main thing is that you must first technical support clarify in advance which communication protocol the telecom operator uses.
Most often, either "Automatic IP (DHCP)" or "PPPoE" is used.
In the first case, usually, you don’t need to specify anything additional, but in the second, you will need to enter the login and password for the connection, which you were given when concluding an agreement with the provider. Click on "Next".
In the next step, we will configure the Wi-Fi wireless network:
Here you will need to enter the network name SSID and the password for it is Network key. If you are setting up a dual-band router, here you will need to enter the name and WiFi password for the 5GHz range. Click on the "Apply" button.
At the last step of the wizard you will see summary information:
This manual is relevant for ASUS RT-N10, RT-N11P, RT-N12, RT-AC51U, RT-AC52U, RT-N56U and RT-N66AU routers, as well as for all other models running on software ASUSWRT (web interface in dark colors).
In order to set up a connection with your provider, go to the “Internet” section, “Connection” tab. It looks like this:
Most branches of the largest Russian providers Rostelecom, TTK and Dom.ru use the PPPoE protocol. Select it in the "WAN connection type" field:
Be sure to ensure that the "Yes" checkboxes for WAN, NAT and UPnP are checked.
Below, please make sure that the “Yes” checkboxes are checked for the “Obtain a WAN IP address automatically” and “Connect to the DNS server automatically” items:
In the "Account Settings" section, you must specify the Login and password for connecting the ASUS router to the Internet, which were given to you when concluding the agreement.
There is no need to change any further parameters. Click the "Apply" button and check your Internet access.
Some branches of the Rostelecom and TTK providers use the "Dynamic IP" connection type, when the router receives the address from the provider's DHCP server and no other connections or protocols need to be used.
To configure, you need to select the WAN type "Automatic IP".
Be sure to check that all the points indicated in the figure are ticked.
Pay special attention to the fact that DNS server addresses should also be obtained automatically by the device.
On the Internet, the Beeline provider uses the L2TP protocol for connection:
We leave obtaining an IP address and DNS server in automatic mode.
In settings account We enter the “Username” (usually this is a personal account) and the password that was issued by the operator’s representatives.
All that remains is to enter the address of the Beeline VPN server: tp.internet.beeline.ru
Click the "Apply" button.
To set up normal WiFi network in the 2.4 GHz range on ASUS routers, you need to select the “Wireless Network” item in the main menu and the “General” tab:
In the SSID field you must enter the name of the Wi-Fi network you are creating. Any word in English can be used in this capacity. Then you need to select the "WPA2-Personal" authentication method and enter the password in the "WPA Pre-Shared Key" field. As a rule, there is no need to change anything else, since the most optimal parameters are set by default.
To configure WiFi 5 GHz on ASUS routers (RT-AC51U, RT-AC52U, RT-AC55U, RT-N56U, RT-AC66AU and AC68U), you need to go to the " frequency range"set the value 5 GHz:
And then everything is exactly the same as usual: we enter the “SSID” (it is desirable that it is slightly different from the one used on 2.4 GHz), indicate the verification method “WPA2-Personal” and the WiFi password, Click the “Apply” button .
Old web interface
If you are using old firmware ASUS routers are made in blue tones (RT-G32, WL-520GC, etc.), then in this case just proceed by analogy. Here are some video instructions that you may find useful:
As you can see from the video - by the designation of key parameters in different versions There is no difference in firmware.
This question is especially of concern to novice users, and most of all to those who recently bought a router to organize a home local network (+ Internet access for all devices in the apartment) and want to quickly set everything up...
I remember myself at that moment (4 years ago): I probably spent about 40 minutes figuring it out and setting it up. In the article I would like to dwell more not only on the question itself, but also on the errors and problems that usually arise during the process.
So, let's begin…
Buy a router... :)
The first thing you do is connect all computers to the router to LAN ports (connect the LAN port of the router with an Ethernet cable to the LAN port of your network card).
Usually there are at least 4 LAN ports on most router models. The router comes with at least 1 Ethernet cable (regular twisted pair), which means it will be enough for you to connect one computer. If you have more: don’t forget to buy Ethernet cables at the store along with your router.
Your Ethernet cable through which you were connected to the Internet (previously it was most likely connected to network card computer directly) - should be plugged into the router’s socket called WAN (sometimes called Internet).
After turning on the router's power supply, the LEDs on its case should start blinking (if you have connected the cables, of course).
In principle, you can now proceed to setting up the Windows OS.
The first setup of the router must be done on desktop computer connected to it via an Ethernet cable. In principle, you can do it from a laptop, only then you still connect it via cable, configure it, and then you can do it wirelessly wired connection go...
This is due to the fact that by default, Wi-Fi network In general, it may be disabled and you, in principle, will not be able to enter the router settings.
First we need to configure the OS: in particular network adapter Ethernet through which the connection will go.
To do this, go to the control panel at the following path: " Control Panel\Network and Internet\Network Center and shared access ". Here we are interested in the link " Change adapter settings"(located in the left column if you have Windows 7, 8).
Go to the properties of Internet Protocol version 4.
And here you can set to automatically obtain an IP and DNS address.
Now you can go directly to the settings process itself...
And so, launch any browser installed on your computer ( Internet Explorer, Chrome, Firefox). Next, enter the IP address of your router’s settings page into the address bar. Typically this address is indicated on the documentation accompanying the device. If you don’t know, here is a small plate with popular router models. Let's look at another method below.
Table of logins and passwords (default).
If you manage to log in, you can go to the settings of your router. You may be interested in articles on setting up the following routers: , .
There are two ways...
1) Go to command line(in Windows 8, this can be done by clicking on “Win + R", then in the “open” window that opens, enter “CMD" and click Enter key. On other operating systems, the command line can be opened through the start menu).
What interests us most here is the line with the “main gateway”. It contains the address of the page with the router settings. IN in this case(in the picture below): 192.168.1.1 (type it into the address bar of your browser, see password and login just above).
2) If all else fails, you can simply reset the router and return it to factory settings. To do this, there is a special button on the body of the device; in order to press it you need to try: you need a pen or a knitting needle...
On the D-Link DIR-330 router, the reset button is located between the outputs for connecting the Internet and the device’s power supply. Sometimes the reset button may be located on the bottom wall of the device.
Having considered the question of how to enter the router settings, I would like to emphasize once again that usually all the necessary information is in the documents that come with the router. It’s another matter if it is written in a “barbaric” (not Russian) language and you don’t understand anything about it or you bought the router secondhand (borrowed from friends/acquaintances) and there were no pieces of paper there...
Therefore, the saying here is simple: buy a router, preferably in a store and preferably with documentation in Russian. There are a lot of such routers now and different models, the price can vary significantly, from 600-700 rubles - to 3000-4000 rubles. and higher. If you don’t know and are just getting acquainted with such a device, I advise you to choose something in the mid-price category.
That's all. I'm going to settings...
In this article, we suggest that you familiarize yourself with the instructions for setting up an Asus router by logging into the admin panel of the router using the instructions provided for this.
In this article, we suggest that you familiarize yourself with the instructions for setting up an Asus router by logging into the admin panel of the router using the data provided for this.
Routers from manufacturer Asus some of the most popular and widespread in our country, especially the models: RT-AC51U, RT-AC68U, RT-N12, RT-N16, RT-N11P, RT-AC3200, RT-N14U, RT-N66U, RT-AC87U, RT -AC66U, RT-N56U, RT-N56U. The process of setting them up is not much different from setting up equipment produced under other brands, but there are still differences. Therefore, we decided to create separate instructions for Asus routers.
We configure Asus equipment as standard:
Please note that you can enter the settings and change them not only from a desktop PC, but also from any mobile device: tablet, smartphone. However, it is more convenient to do this using a desktop PC or laptop. In this case, it is better that the device is connected via a cable, but if you use wireless connection, then keep in mind that you should not update the router’s firmware using Wi-Fi, because There is a high probability of receiving non-working equipment instead of a working device.
To connect to the interface Asus router, first you need to connect to this router using...
Company ASUS presents the RT-N12 C1 router, designed for use at home or in a small
If you have previously set up a connection to an Asus router, then this will not be a problem for you. In the case of a new router, immediately after turning it on, it will start looking for a wireless network, which in most cases will be called Asus.
The network will be without a password, and you just need to join it by clicking on the network and selecting " Connect«:
If you don’t remember the Wi-Fi password and there is no way to find it out using other connected devices, then you will have to use a wired connection. If there is no cable, then you can do this: reset all the router settings to factory settings and set the settings again. To reset your ASUS device to factory settings, you need to press and hold 10 Seconds button RESET .
Where can I get the address that is written in the address bar of the browser to access the settings? It is indicated on the body of the router itself. Here:
The answer to this question depends on what kind of error you have and at what stage of the process. Some users encounter problems connecting to the router; many do not open settings in one browser or another and the message “ the page is not available". These are the most common problems and to fix them you can try the following:
